MAKE YOUR OWN SPINNER BAITS



MAKE YOUR OWN SPINNER BAITS 

“ Old Fashioned Hand Job

have accumulated over the years, many tools because I work on many projects using wire not just fishing, but at seventy-eight, I have indulged in sixty-five years a multitude of disciplines.  From  maintaining my own Piper and Cessna aircraft and boats to Arduino PC and Mac Computers, electronics,  jewelry, upgrades and mechanical and electronic exploration.  My tools have been invaluable for many reasons, makes work simple, saves my hands, keeps me creative, supports my hobby, and recreation, avoids depression and an active mind is a healthy one.  Working with wire, the basis of spinners and buzz baits used both as a part of support but as a heat conductor and as an electronic carrier.

I take care of my tools, multi-use pliers in small and large, like new, some are customized for specific purpose,  so I needed nothing to do as far as wire bending, without spending a dime.  I just bought the wire beads, trebles, clevises and blades and made twenty the first day.  I have over a hundred twenty spinners in addition to many flies, spoons, jigs, etc. about five or six hundred lures. And enough supplies for another hundred.  I am planning a charity event.  And these spinners will go to the kids and parents who attend

By now you must think I am either very frugal, anti-establishment or simply nuts.  None of the above… I like to amuse myself either reinventing the wheel and a lot of wheels today are corporately still square shaped.  I am simply not interested in BS and I have a set of rules and expressions which have worked for me:  One is take a kid fishing, and lures are readily and financially available.

Making your own lures, these are very interchangeable, varied and I have a boxes full of double spinner blades with weights, fast snaps and place in front of the flies… These are about a fifth, it seems to grown everyday of my D-I-Y fly’s spinners and components…rigs can both used for spinning rods adding a weight and fly  rods… unconventional but sometimes it works.  

When trash fishing, new explorations, or territory, searching or killing time I use the cheaper home made lures so a hangup is a eighty-five cent loss not five six or seven dollars.   Also I make combinations not seen for stimulus or territorial strikes. On my first page I speak of a gentleman Carl Hansen.  His key to fly fishing success was he was his own man, designed much of what he used and had a degree in fish psychology… It goes for some, who can afford it that fishing is a challenge, and in one of my favorite articles I wrote about fishing lures and dog food.

Yes, some of the fish are smarter than their fisherman, but fish are lost and not hooked on the theory of staying alive… I don’t suppose you take your dog to the supermarket and let him decide what box of carbon grits he likes.  Fancy packages and fancier pictures mean nothing to the dog,  except it is aimed at the dog owner who pays for the stuff.  Same thing with lures, many try to imitate nature which is correct, but doesn’t always win, i am constantly experimenting going very wild  and unconventional at times. Many times… thats how you learn…  


These Are Basic Tools You Need, Probably Have some To Get Started 

1— Pliers are the core of spinners, cranks and most bait production because every automated expensive tool or gadget on the market does the same thing your pliers can do as to and offer strength for your hands. Using my hands more has helped my arthritis incredibly so.  No - mo - meds…..

2— Initial shapes and ends have to start somewhere and for some your hands won’t cut it.  Thats why we have tools and how did we survive before all this expensive stuff…

3— From scraps I built myself a wire board that does everything, from selling to Haywire to 24-35-52 spinner bending.   My working boards are not just for fishing but all the other things I am involved with.

LURE MAKER Magnetic bench.

7-  On the other hand during COVID -19, I managed to keep my sanity and two hundred “ Kures and Lures”  later… I call it… I kept busy using my hands and mind, learning new techniques avoiding TV listening to good music and inspiring speakers of History,  I am and speak on the atrocities of that era.  World War Two… I am a writer in the greatest Brooklyn tradition, of telling it like it is and I work with two organizations as fact checker and researcher.  And  because I write about stressful Politics, Bad Food and Aviation Mishaps…the fishing and lure building keeps me from going  off the rails.   


Get Wired ( All on Amazon or Jann’s Net-Craft and Stoddards )

This Is Not Rocket Science - Spinner Bait ( MeppsType) From Closed Loop Wire Shaft or Open Loop (R-loop) or Straight Shaft and these tools can put some love in your life.  All start with wire… and a pair of pliers…

I’ll show you a variety all available at Amazon, these are NOT fishing only like some companies push, thats BS but crimpers and hook removers don’t make Jewelry either.  The pliers I wear on my belt for fishing from Booms are made for fish.  Here you will be making lures and jewelry…

Bonus:  It can be a family affair… Let wife use them as these are jewelry grade and Bead Smith sells all the supplies for both jewelry and I use some stuff to make lures from.  Just tell her you’ll make Jewelry for her including earrings and you will be a hero and receive no flack, it works…



Purchase ready made shafts to skip this step and all you will need are from list of suppliers on first page .
Open loops work from the Hook Up  
— Closed loops work from the eyelet down to the hook.


PLIERS  — Bench Sorter  — DIY Tool For Spinners

ROUND AND FLAT NOSE PLIERS With great choices at Amazon.COM.  I can reccomend Bead Smith is quality gear and inexpensive.  Great choice, three differnt styles shown here.  Biggest In The Jewelry Business… Another jewelry tool, the board I use to layout my lure with parts sections, round stuff rolls off tables. 

Their pliers run six to nine dollars, you only need three, I showed you three types of Round, you only need one.  That bead dish for eight dollars lets you lay out the patterns.  On a fishing site I saw one out of mahogany for fifty-eight dollars…must be for the 2% wealthy, this one cost seven dollars and change.   

The pliers make the initial loop, here are three choices including the Lopper auto model plus the flat nose is indispensable once you get into this.   Like I said most hobbyists have a good selection of these tools. If small mostly doing nothing




OPTIONS, MISTAKES AND IDEAS

  • Good Nippers / Or Diagonal Cutters
  • A Small Flat File For Trimming Ends Of The Barrel Wrap If Cannot Twist Off
  • Needle Nose Pliers With Rough Grip Or Scored To Grip
  • Chinese Miniature Vice Grips  Knockoffs But Work Ok From Lowes
  • An Ordinary Awl…   Sometimes Not So Round Eyelets Need A Nudge To Round Like in the picture. Just make the barrel turns, three and the use the awl to round out the end, straighten with flat pliers.
  • The 3Mm Looper Plier Does  A Few Things More And Is The Most Expensive At 22.99 About The Price Of Three Mepps Fancies.  But Not Essential. I Do However Favor It For Open Loop Shafts And Some Tube Style Lures I Make.
  • Round Nose Essential — Needle Nose Does Not Make A Good Loop — Correct With The Awl — We Want A Circle Not The Letter “D” And An Awl Works Best Over A Mini-Vise.


—  I Made Hundreds Of These Spinner Baits - No Losses —


SAFETY NOTE:    —  I NEVER WORK WIRE WITHOUT SAFETY GLASSES —

  • I only just stabbed myself a few hundred times with 38-48 lb wire. Good practice avoids this.
  • The Smaller Wire 4/5/6/  is the width of a hypodermic needle.
  • Working with wire in RC parts and JEWELRY, I learned how fast you can stab yourself with torsioned wire.
  • Never when using diagonal cutters ever leave the tag end facing you, it becomes a missle and will puncture you and do some damage.  The first time I cut some, they went flying and the wire made my wall look like a dart board.
  • I pre-cut some lengths over a pail thats mounted on the side of my primary bench, tag end or cut end down, since the smaller piece takes off like a rocket.


TYPE A:  Shaft With Open Or “R” Eye Loop  -  Working With Hook First From The Bottom

Step 1: Place hook eye in eye of open loop wire shaft
Step 2: Pinch the two ends of the wire shaft together and slip the desired brass spinner body or bodies down the shaft.
Step 3: Slide remaining body components and the desired spinner blade with properly sized stirrup clevise onto the shaft. Step 4: Using looper pliers grab the wire shaft about 5/16”— 8mm to11mm above the clevise and bend the wire three quarters (270°) around the nose of the pliers.. We can align later after we tie the tag end off.
Step 5: Now Wrap the tag end of the wire shaft tightly around the shaft. Wrap three complete turns.  That was easy…



TYPE B:  Shaft With Closed Eye Loop  —  Working From The Top of the Lure To The Hook 

Step 1: Place small bead below loop, brass spinner or glass bead 
Step 2: Slip the desired brass or nickel clevis and blade on the shaft bodies down the shaft.
Step 3: Use another brass bead on the botto of the clevis, you should have a clevis with brass beads acting as bushings.  Step 4: Now add beads, three or four, or brass, painted bodies, tubes. etc and finish with a bead.
Step 5: Use the round nose or looper pliers grab the wire shaft about 5/16”( 8mm) above the clevise and bend the wire three quarters (270°)around the nose of the pliers.. We can align later after we tie the tag end off.
Step 6:
Using the rough needle nose simply use the tag end to form three close turns around the end.
Step 7:  I use a number two-three or four split ring as it allows movement and  changing hook sizes to switch to a single hook with feathers etc. That was easy


— The Jacobs Tool —  Makes Beautiful Barrel Loops

Make sure the ball head on the X-acto #2 is just a one cut and not a cross with a hole in it, this is why we only use the number two from X-Acto, other sizes or brands won’t work.

                


Good Sources